If the message below appears on the LCD display, upgrade the firmware first. Turn on the power while shorting-circuit connector CN 2-pin connector on the PRT board with tweezers. Stop the short-circuit operation and upgrade the firmware again. After increasing or decreasing the parameter, be sure to check the printing. Check the printing. CPU block.
Memory DRAM block. Memory control ASIC block. Sampling clock generation block. Color adjustment block. The resultant signal is converted from digital to analog again as an analog signal and output to the analog signal processing block.
After that, the image data is adjusted in color using a color adjustment circuit IC , and the image size is adjusted by the blanking produced using a DRAM control circuit. The resultant data is converted from digital to analog and output to the analog signal processing block. OEP-3 V1 UC Page The video signal input from an analog signal processing block is converted from analog to digital as an eight-bit digital signal.
The converted video signal is converted from 8 bits to 32 bits and decimated e. Asynchronous serial communication. Start bit:. Data bit:. Stop bit:. Parity bit: None. Each setting is not restricted by video timing. The setting value is latched using a VD signal and validated after the VD signal. The conversion of eight bits to 32 bits and vice versa is performed using a DRAM control circuit. The flow of data shown below is obtained according to the print color. The clock frequency is The operation timing is shown below.
Paper feed timing sensor. Delivery timing sensor. Paper feed FG sensor. Paper sensor. Tray position sensor Reflective type. Platen chuck sensor. Paper jamming sensor Transmission type. Print paper does not exist at a delivery port.
Print paper does not exist and a paper feed tray is not set. Print paper exists in the chuck position. Therefore, this circuit controls the current-carrying time of a head element and corrects the print density. The frequency-divided clock varies depending on the baud rate setting. The two types of remote controls can be connected. The 12 V system on the SY board is used only in an antenna drive circuit. Video mode IF board Purpose Confirms the video mode set by the user. The paper remove tray is the same as the UP series.
An anti-jamming cover is provided at the bottom of the printer located under the platen and shown by the broken line. Cools the thermal head during printing and prevents overheating. Page 6: Repair And Modification — Keep fluids away from all electrical equipment.
If The following signal words are used throughout this fluids are spilled on or into this instrument, manual: immediately stop operating it and contact Olympus. Page 7 — Do not apply excessive force to the terminals of this instrument. The medical agents possibly may come into this instrument from its ventilation grills and cause the failure. Page 8: Chapter 1 Package Contents Match all items in the package with the components shown below.
Inspect each item for damage. If this instrument is damaged, a component is missing or you have any questions, do not use this instrument; immediately contact Olympus. Color video printer Trial pack sheets Ink ribbon holder Page 9: Chapter 2 Installation And Connection 2. Be sure the portion of the color video printer OEP- 4 does not contact with the mobile workstation, etc.
In addition, never use the other printing packs except UPC For the first time using this instrument, supplied trial pack can be used for an operation check. Page 16 see Figure 3.
Also refer to the caution label on the ink ribbon holder. Caution label Figure 3. Front door Figure 3. Page 18 Open the cover of the paper tray. Insert the paper tray into the color video printer If print sheets remain in the paper tray, remove OEP-4 until it clicks see Figure 3. Align the direction of the arrow of the positioning Page 3.
Refer to the instruction manuals of the connected equipment and set them up as required for use with this instrument. Olympus offers a broad range of services to healthcare professionals and to our customers, including contact hour and peer-based training courses; information, training tools and videos on infection control and reprocessing; authorized repair services and support on Olympus equipment; and financing solutions to help your facility with acquisition of new capital equipment, accessories, and maintenance plans.
Olympus offers a broad range of services to healthcare professionals and to our customers. Skip to main content. Contact Contact Us Today. Careers Learn More.
Thunderbeat Tissue Management. BF Bronchoscopes. VisiGlide Guidewires.
0コメント